Display and control
The status of the Highway Lane Change Assist system in your Kia Telluride is conveniently monitored directly through the instrument cluster. For a deeper understanding of these visual cues and how to navigate the settings, please refer to the comprehensive LCD display modes section in your owner's manual.
The Kia Telluride provides clear, real-time feedback regarding the Highway Lane Change Assist status on the instrument cluster as follows:
|
|
Highway Lane Change Assist indicator
Green (
): Ready to assist.
Green (
) blinking: System is actively maneuvering the vehicle.
Gray (
): Standby (function is enabled but conditions are not currently met).
White (
) blinking: Canceled (this visual alert persists briefly following a system cancellation).
Lane line
The visual representation of the lane lines on your Kia Telluride display will match the color-coding of the Highway Lane Change Assist indicator (1). Notably, when the system is in Standby mode, the display will still indicate whether lane detection is currently available.
Green arrow and shade
A green arrow and accompanying highlight appear once the system has initiated the maneuver, remaining active until the lane change is successfully completed by your Kia Telluride.
Message
An informative message will appear on the cluster if Highway Lane Change Assist is unable to engage after you have activated the turn signal lever.
An alert message will be displayed if the system is forced to cancel while a lane change maneuver is currently in progress.
To turn the Highway Lane Change Assist ON, you can easily access the system settings via the Driving Assist or Lane Driving Assist button located on your steering wheel or dashboard console.
Turning ON Highway Lane Change Assist
|
|
The Highway Lane Change Assist feature in your Kia Telluride is fully prepared to operate when the system is set to ON and the following comprehensive criteria are met:
Highway Driving Assist is currently active.
Lane Following Assist is currently active.
Your Kia Telluride is ON and the sensors have successfully detected a vehicle behind you at least once.
Your driving speed is greater than 20 mph (30 km/h).
When traveling at lower highway speeds (20-40 mph or 30-60 km/h), the vehicle must recognize objects in the adjacent lanes and confirm there is no risk of a side-impact collision.
The instrument cluster is not actively displaying a "hands-off" steering wheel warning.
Hazard lights are verified to be OFF.
TIP
When the Lane Change Assist function is ON, the Lane Following Assist feature will remain active even if you use the turn signal or hazard lights.
Lane Change Assist will automatically deactivate if you enter any of the following conditions:
You are driving on a road with only one driving lane.
The road lacks physical center separation structures, such as median strips or guardrails.
The vehicle sensors detect a pedestrian or cyclist in the path ahead.
If your speed drops below 15 mph (25 km/h) while the system is in the "Ready" state, the function will automatically shift into standby mode.
While driving between 20-40 mph (30-60 km/h), if the Kia Telluride fails to detect vehicles in the adjacent lanes, the system will switch to standby.
The status will immediately revert to standby if the sensors identify a potential risk of collision.
Please note that visual styles, icons, or color palettes on the display may vary slightly depending on your specific instrument cluster configuration or selected digital theme.
WARNING
Whenever the Highway Lane Change Assist system turns OFF, Steering Assist functionality will also be temporarily suspended. You must remain vigilant and ready to take full manual control of the steering at all times.
Highway Lane Change Assist operation
|
The Highway Lane Change Assist function operates seamlessly when the system is in the "Ready" state, you engage the turn signal lever to position (1) or (2), and the following conditions are confirmed:
Your hands are detected on the steering wheel.
The sensors verify that the target direction is clear of collision risks.
You are driving on a multi-lane road where the lane markings in the direction of your desired change are broken lines (regardless of color).
There are no active alerts from the Forward Collision-Avoidance Assist or Blind Spot Collision-Avoidance Assist systems.
The vehicle is currently centered in its lane, rather than drifting near the edges.
The current road infrastructure meets the specific operational mapping requirements for Highway Lane Change Assist.
TIP
When you move the turn signal lever to position (1), the system initiates. If you return the lever to the neutral position before the vehicle crosses the lane line, the maneuver will cancel.
The system will not cancel after you have crossed the lane line; instead, it will conclude the maneuver and automatically turn the turn signal OFF once the lane change is finished.
When the lever is held in position (2) for the required duration, the green arrow will appear on your display. The Kia Telluride will continue the maneuver even if you release the lever back to its neutral position.
During the lane change, the turn signal indicator will continue to blink automatically even if you do not hold the lever, and it will shut off once the Kia Telluride has successfully centered itself in the new lane.
Highway Lane Change Assist standby
Your Kia Telluride will place the Highway Lane Change Assist into a standby state if a "Ready" condition is not met or if you are navigating specific road environments, including:
Main highway segments located in close proximity to a toll plaza.
Roadways that terminate without a formal interchange or junction.
Road sections with extreme or sharp curvature.
Areas where lane width is restricted or narrow.
Canceling Highway Lane Change Assist
The Highway Lane Change Assist will be canceled under the following conditions:
You manually move the turn signal lever toward the direction opposite your current lane change.
You apply excessive or sharp steering input.
You activate the turn signal (1) while the system is already operating, then return it to the neutral position before the lane change has successfully occurred.
WARNING
Highway Lane Change Assist will be immediately canceled under any of the following circumstances:
You manually switch the Highway Driving Assist system OFF.
You turn OFF or pause the Lane Following Assist or Smart Cruise Control features.
The instrument cluster triggers a "hands-off" steering wheel warning message.
You engage the turn signal lever to the (1) position while in an active state.
You manually turn the vehicle's hazard lights ON.
A warning message from the Forward Collision-Avoidance Assist or Blind-Spot Collision-Avoidance Assist is displayed.
The vehicle sensors detect a potential collision risk in the adjacent lane, even in the absence of a formal Collision-Avoidance Assist warning.
The target lane path comes to an end.
The system is unable to detect or map the target lane.
A technical fault is detected in the vehicle's turn signal lighting.
The feature is disabled in the vehicle settings menu, you enter a one-way road, an intersection or crosswalk is detected, a pedestrian/cyclist is in the driving path, or you move onto a road lacking physical lane-dividing structures like guardrails or medians.
Driving speed falls below 15 mph (25 km/h) while the system is in the "Ready" state.
Driving between 20-40 mph (30-60 km/h) without the vehicle detecting other traffic in the adjacent lanes.
The sensors detect an imminent risk of collision.
Should you cancel the Highway Lane Change Assist while it is in the middle of a maneuver, the vehicle may automatically steer back toward the lane center or disengage steering assistance entirely depending on the current road conditions. Always maintain your focus on the road and stay prepared to intervene.
Note that Highway Lane Change Assist may not function with standard precision on roads frequented by pedestrians or cyclists, such as near intersections or marked crosswalks.
Highway Driving Assist malfunction and limitationsNOTE
You can set the units for both the multifunction display (black and white) and the combination meter at the same time. For details about setting the language and units, refer to “Type A combination meter” or “Menu screens”.